Users Guide to Perform Linksys Mesh WiFi 6 Setup
If you have wished for an uninterrupted internet range to access, then we suggest you consider doing Linksys mesh WiFi 6 setup. Here, in this blog, we have provided instructions following which the setup process of your Linksys device will be a walk in the park for you.
Linksys Mesh WiFi 6 Setup via WPS
WPS is one of the simplest ways to configure Linksys mesh WiFi 6 device. Go through the following instructions and know how to configure your Linksys device with ease:
- Plug your Linksys device into an electrical outlet.
- Press the power button and connect the Linksys device to your internet modem.
- Next, find the WPS button on your mesh router.
- Once found, press it very gently.
If the WPS LED on your Linksys mesh WiFi 6 device turns green, it means that you have successfully configured the device using the WPS method.
In case you get any issues while setting up your Linksys device using the WPS method, reach out to our expert technicians now.
Now, the next method in our blog post to configure your WiFi 6 device is using the manual method. For instructions, scroll down a little.
Linksys Mesh WiFi 6 Setup via Manual Method
- Place your mesh WiFi 6 device in the same room as your internet modem.
- Press the power button on your Linksys device to turn it on.
- Create an Ethernet connection between your Linksys and existing device (modem).
- Switch on a laptop or desktop.
- Launch an internet browser of your choice.
- Type the default IP of your WiFi mesh router in the browser’s URL bar.
- Press Enter.
- Log in to your Linksys device using the default username and password. The login credentials of your Linksys device are case-sensitive. So, be very careful while entering them.
- The WiFi mesh 6 router setup page will appear.
- Reaching here, follow the instructions in the exact given order. Have patience! Do not interrupt the configuration process of your device.
That’s it! You are all set! You have successfully configured your Linksys mesh WiFi 6 device using the manual method.
Although the configuration process of your Linksys device isn’t a big deal, however, 90 percent of users have troubles during the process. On the off chance that you are also sailing on the same boat, follow the troubleshooting tips highlighted below.
Can’t Perform Linksys Mesh WiFi 6 Setup?
- Make sure that your Linksys device is receiving an uninterrupted power supply. The wall plug to which the router is plugged in must be well-working.
- The internet browser you are using to log in to your WiFi device must be up-to-date.
- If you get issues while accessing the IP address of your Linksys device, clear browsing history and do not make use of a private window.
- Ensure that there is no difference between your internet modem and the Linksys device and they must be connected properly using an Ethernet cable.
- Make sure that the device you are using for setting up your Linksys device has the latest software version installed on it.
- See the manual of your Linksys device. Over there, you can get details about the default login credentials.
- Restart your Linksys device if you see that the power LED on it continues to blink for longer than expected. For this, disconnect your Linksys router and modem and unplug it (WiFi mesh 6 device). Wait for some time and then, plug the router back in again. After a few minutes, the power LED on it will surely become stable.
After following the tips provided above, you will surely be able to fix setup-related issues with your Linksys device.
Our blog on how to perform Linksys mesh WiFi 6 setup ends here. If you still have queries regarding the same, feel free to reach us anytime.
Want More?
These days, we are receiving queries from a million of users across the globe that Christmas Eve is around the corner. We want to enjoy the internet range outside our homes and in the park of our apartment/society. Because there will be an event over there. So, we want to make reels and videos. Is there any way out? And, we said yes! There is a way and that is setting up Linksys extender via extender.linksys. Just perform it and experience the change yourself.
